EN EN G17NiCrMo1.V6Enquiry|Print this page
| Category | Type | Steel grade | Standard | Country |
|---|---|---|---|---|
| Grades | Special Alloy | EN G17NiCrMo1.V6 | EN | Euronorm |
Chemical composition%of the ladle analysis of gradeEN G17NiCrMo1.V6
| C(％) | Si(％) | Mn(％) | P(％) | S(％) | Cr(％) | Ni(％) | Mo(％) |
|---|---|---|---|---|---|---|---|
| 0.15-0.19 | 0.50 | 0.55-0.80 | 0.015 | 0.015 | 1.30-1.80 | 3.00-3.50 | 0.45-0.60 |
| Proof strength Rp0.2(MPa) | Tensile strength Rm(MPa) | Impact energy KV(J) | Elongation at fracture A(%) | Reduction in cross section on fracture Z(%) | As-Heat-Treated Condition | Brinell hardness(HBW) |
|---|---|---|---|---|---|---|
| 349(≥) | 311(≥) | 44 | 14 | 13 | Solution and Aging,Annealing,Ausaging,Q+T,etc | 241 |
| Property | Density kg/dm3 | Temperature T °C/F | Specific heat J/kgK | Thermal conductivity W/mK | Electric resistance µΩ·cm | Modulus of elasticity kN/mm2 | Expansion rate |
|---|---|---|---|---|---|---|---|
| 962(≥) | 328(≥) | 22 | 41 | 42 | Solution and Aging,Annealing,Ausaging,Q+T,etc | 323 | |
| Temp. °C/°F | Creep strain limit (10000h) (Rp1,0)N/mm2 | Creep rupture strength (10000h) (Rp1,0)N/mm2 | |||||
| 938 | 154 | 865 |
| Product type | Products | Dimension | Processes | Deliver Status |
|---|---|---|---|---|
| Plates/Sheets | Plates/Sheets | 0.08-200mm(T)*W*L | Forging,hot rolling and cold rolling | Annealed,Solution and Aging,Q+T,ACID-WASHED,Shot Blasting |
| Steel Bar | Round Bar,Flat Bar,Square Bar | Φ8-1200mm*L | Forging,hot rolling and cold rolling,Cast | Black,Rough Turning,Shot Blasting, |
| Coil/Strip | Steel Coil/Steel Strip | 0.03-16.0x1200mm | Cold-Rolled&Hot-Rolled | Annealed,Solution and Aging,Q+T,ACID-WASHED,Shot Blasting |
| Pipes/Tubes | Seamless Pipes/Tubes,Welded Pipes/Tubes | OD:6-219mm x WT:0.5-20.0mm | Hot extrusion,Cold Drawn,Welded | Annealed,Solution and Aging,Q+T,ACID-WASHED |
| Grade | Standard | Country | Application |
|---|---|---|---|
| NV6(5150) | EN | Euronorm | Steel for intake valves |
| HNV6 | EN | Euronorm | Steel for intake valves |
| S65006 | EN | Euronorm | Steel for intake valves |
| EV6 | EN | Euronorm | Steel for exhaust valves |
| S63015 | EN | Euronorm | Steel for exhaust valves |
| HEV6 | EN | Euronorm | Steel for exhaust valves |
| N07090 | EN | Euronorm | Steel for exhaust valves |
| 38CrSiV6 | EN | Euronorm | Alloyed CrSiV steel |
| 45SiCrV6 | EN | Euronorm | Alloyed CrSiV steel |
| 27CrMoV6-12 | EN | Euronorm | Alloyed CrMoV steel |
| 54NiCrMoV6 | EN | Euronorm | Alloyed NiCrMoV steel |
| 55NiCrMoV6 | EN | Euronorm | Low alloyed NiCrMo steel |
| 1.7715 | EN | Euronorm | Alloy special steel |
| 14MoV6-3 | EN | Euronorm | Alloy special steel |
| 15CDV6 Air 9160/C | EN | Euronorm | wrought steels used in aeronautical constructions |