EN EN X2CrNiMoN17-11-2Enquiry|Print this page
| Category | Type | Steel grade | Standard | Country |
|---|---|---|---|---|
| Grades | Special Alloy | EN X2CrNiMoN17-11-2 | EN | Euronorm |
Chemical composition%of the ladle analysis of gradeEN X2CrNiMoN17-11-2
| C(％) | Si(％) | Mn(％) | P(％) | S(％) | Cr(％) |
|---|---|---|---|---|---|
| 0.030 | 1.00 | 2.00 | 0-045 | 0.015 | 16.5-18.5 |
| Proof strength Rp0.2(MPa) | Tensile strength Rm(MPa) | Impact energy KV(J) | Elongation at fracture A(%) | Reduction in cross section on fracture Z(%) | As-Heat-Treated Condition | Brinell hardness(HBW) |
|---|---|---|---|---|---|---|
| 736(≥) | 645(≥) | 12 | 33 | 13 | Solution and Aging,Annealing,Ausaging,Q+T,etc | 233 |
| Property | Density kg/dm3 | Temperature T °C/F | Specific heat J/kgK | Thermal conductivity W/mK | Electric resistance µΩ·cm | Modulus of elasticity kN/mm2 | Expansion rate |
|---|---|---|---|---|---|---|---|
| 595(≥) | 623(≥) | 22 | 11 | 44 | Solution and Aging,Annealing,Ausaging,Q+T,etc | 312 | |
| Temp. °C/°F | Creep strain limit (10000h) (Rp1,0)N/mm2 | Creep rupture strength (10000h) (Rp1,0)N/mm2 | |||||
| 557 | 546 | 794 |
| Product type | Products | Dimension | Processes | Deliver Status |
|---|---|---|---|---|
| Plates/Sheets | Plates/Sheets | 0.08-200mm(T)*W*L | Forging,hot rolling and cold rolling | Annealed,Solution and Aging,Q+T,ACID-WASHED,Shot Blasting |
| Steel Bar | Round Bar,Flat Bar,Square Bar | Φ8-1200mm*L | Forging,hot rolling and cold rolling,Cast | Black,Rough Turning,Shot Blasting, |
| Coil/Strip | Steel Coil/Steel Strip | 0.03-16.0x1200mm | Cold-Rolled&Hot-Rolled | Annealed,Solution and Aging,Q+T,ACID-WASHED,Shot Blasting |
| Pipes/Tubes | Seamless Pipes/Tubes,Welded Pipes/Tubes | OD:6-219mm x WT:0.5-20.0mm | Hot extrusion,Cold Drawn,Welded | Annealed,Solution and Aging,Q+T,ACID-WASHED |
| Grade | Standard | Country | Application |
|---|---|---|---|
| 1.4406 | EN | Euronorm | DIN 1654-5 (1989) Cold heading and cold extruding steels; technical delivery conditions for stainless steels; Replaced by DIN EN 10263-5:2002 |
| X2CrNiMoN17-11-2 | EN | Euronorm | DIN 1654-5 (1989) Cold heading and cold extruding steels; technical delivery conditions for stainless steels; Replaced by DIN EN 10263-5:2002 |
| X2CrNiMoN17-11-2 | EN | Euronorm | Stainless steel bars for pressure purposes |
| 1.4406 | EN | Euronorm | Stainless steel bars for pressure purposes |
| X2CrNiMoN17-11-2 | EN | Euronorm | Stainless steel bars for pressure purposes |
| 1.4406 | EN | Euronorm | Stainless steel bars for pressure purposes |
| X2CrNiMoN17-11-2 | EN | Euronorm | Stainless steels - Chemical composition |