AISI 501Enquiry|Print this page
| Category | Type | Steel grade | Standard | Country |
|---|---|---|---|---|
| Grades | Special Alloy | 501 | AISI | USA |
Chemical composition%of the ladle analysis of grade501
| C(％) | Si(％) | Mn(％) | P(％) | S(％) | Cr(％) | Mo(％) |
|---|---|---|---|---|---|---|
| 0.15 | 0.50 | 0.30-0.60 | 0.030 | 0.50 | 4.00-6.00 | 0.45-0.65 |
| Proof strength Rp0.2(MPa) | Tensile strength Rm(MPa) | Impact energy KV(J) | Elongation at fracture A(%) | Reduction in cross section on fracture Z(%) | As-Heat-Treated Condition | Brinell hardness(HBW) |
|---|---|---|---|---|---|---|
| 353(≥) | 332(≥) | 11 | 42 | 44 | Solution and Aging,Annealing,Ausaging,Q+T,etc | 443 |
| Property | Density kg/dm3 | Temperature T °C/F | Specific heat J/kgK | Thermal conductivity W/mK | Electric resistance µΩ·cm | Modulus of elasticity kN/mm2 | Expansion rate |
|---|---|---|---|---|---|---|---|
| 182(≥) | 628(≥) | 12 | 21 | 11 | Solution and Aging,Annealing,Ausaging,Q+T,etc | 412 | |
| Temp. °C/°F | Creep strain limit (10000h) (Rp1,0)N/mm2 | Creep rupture strength (10000h) (Rp1,0)N/mm2 | |||||
| 223 | 615 | 584 |
| Product type | Products | Dimension | Processes | Deliver Status |
|---|---|---|---|---|
| Plates/Sheets | Plates/Sheets | 0.08-200mm(T)*W*L | Forging,hot rolling and cold rolling | Annealed,Solution and Aging,Q+T,ACID-WASHED,Shot Blasting |
| Steel Bar | Round Bar,Flat Bar,Square Bar | Φ8-1200mm*L | Forging,hot rolling and cold rolling,Cast | Black,Rough Turning,Shot Blasting, |
| Coil/Strip | Steel Coil/Steel Strip | 0.03-16.0x1200mm | Cold-Rolled&Hot-Rolled | Annealed,Solution and Aging,Q+T,ACID-WASHED,Shot Blasting |
| Pipes/Tubes | Seamless Pipes/Tubes,Welded Pipes/Tubes | OD:6-219mm x WT:0.5-20.0mm | Hot extrusion,Cold Drawn,Welded | Annealed,Solution and Aging,Q+T,ACID-WASHED |
| Grade | Standard | Country | Application |
|---|---|---|---|
| S20501 | AISI | USA | Stainless steel and heat resistant steel |
| A 314 S50100 | AISI | USA | Stainless Steel Billets and Bars for Forging |
| S50100 | AISI | USA | Chromium Heat Resisting Steel |
| A 1018 HSLAS Grade 65 [450] Class 1 A | AISI | USA | Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Carbon, Commercial, Drawing, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength Steel |
| A 501 Grade A | AISI | USA | Hot-Formed Welded and Seamless Carbon Steel Structural Tubing |
| A 1018 HSLAS Grade 65 [450] Class 1 B | AISI | USA | Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Carbon, Commercial, Drawing, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength Steel |
| A 501 Grade B | AISI | USA | Hot-Formed Welded and Seamless Carbon Steel Structural Tubing |
| X2CrNiMoCuWN25-7-4 | AISI | USA | Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel |
| 1.4501 | AISI | USA | Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel |
| 2HR501 | AISI | USA | Specification for nickel-chromium-cobalt-titanium- aluminium heat-resisting alloy cold drawn wire for springs and springs (Nickel base, Cr 19.5, Co 18.0, Ti 2.5, Al 1.5) |
| X2CrNiMoCuWN25-7-4 | AISI | USA | Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel |
| 1.4501 | AISI | USA | Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel |
| T31501 | AISI | USA | Oil-Hardening Tool Steel |
| AISI 501 | AISI | USA | A 194/A 194M (2014) Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both |
| AISI501 | AISI | USA | AISI501 |
| ASTM501 | AISI | USA | ASTM501 |
| AISI501A | AISI | USA | AISI501A |
| AISI501B | AISI | USA | AISI501B |
| 1.4501, 1.4410, S32760, S32750, X2CrNiMoN25-7-4 | AISI | USA | Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel |