AISI Maraging 350Enquiry|Print this page
| Category | Type | Steel grade | Standard | Country |
|---|---|---|---|---|
| Grades | Special Alloy | Maraging 350 | AISI | USA |
Chemical composition%of the ladle analysis of gradeMaraging 350
| C(％) | Si(％) | Mn(％) | P(％) | S(％) | Ni(％) | Mo(％) | Co(%) | B(%) | Al(%) | Ti(%) | Other(%) |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 0.03 | 0.10 | 0.10 | 0.01 | 0.01 | 18.50 | 4.80 | 12.00 | 0.003 | 0.10 | 1.40 | Zr: 0.01 |
Maraging 350/Maraging C350/Vascomax C350™
Common Trade Names: Vascomax® 350
Maraging C350™ is a nickel-maraging alloy. Maraging C350™ is a relatively soft but tough material, therefore, readily machined and formed. The aging process of Maraging C350™ raises the hardness to a level sufficient for many tooling applications.Typical applications of maraging steels are missile and rocket motor cases, wind tunnel models, landing gear components, high performance shafting, gears, and fasteners.
Available forms are seamless pipe, welded pipe, seamless tube, welded tube, bar, wire, sheet, plate, forgings, pipe fittings and flanges.
 |
|
|---|---|
Sheet/Plate content |
MIL-S-46850 |
Round Bar/Wire content |
MIL-S-46850 |
| Proof strength Rp0.2(MPa) | Tensile strength Rm(MPa) | Impact energy KV(J) | Elongation at fracture A(%) | Reduction in cross section on fracture Z(%) | As-Heat-Treated Condition | Brinell hardness(HBW) |
|---|---|---|---|---|---|---|
| 348(≥) | 653(≥) | 11 | 33 | 43 | Solution and Aging,Annealing,Ausaging,Q+T,etc | 244 |
| Property | Density kg/dm3 | Temperature T °C/F | Specific heat J/kgK | Thermal conductivity W/mK | Electric resistance µΩ·cm | Modulus of elasticity kN/mm2 | Expansion rate |
|---|---|---|---|---|---|---|---|
| 946(≥) | 438(≥) | 14 | 24 | 43 | Solution and Aging,Annealing,Ausaging,Q+T,etc | 234 | |
| Temp. °C/°F | Creep strain limit (10000h) (Rp1,0)N/mm2 | Creep rupture strength (10000h) (Rp1,0)N/mm2 | |||||
| 638 | 854 | 763 |
| Product type | Products | Dimension | Processes | Deliver Status |
|---|---|---|---|---|
| Plates/Sheets | Plates/Sheets | 0.08-200mm(T)*W*L | Forging,hot rolling and cold rolling | Annealed,Solution and Aging,Q+T,ACID-WASHED,Shot Blasting |
| Steel Bar | Round Bar,Flat Bar,Square Bar | Φ8-1200mm*L | Forging,hot rolling and cold rolling,Cast | Black,Rough Turning,Shot Blasting, |
| Coil/Strip | Steel Coil/Steel Strip | 0.03-16.0x1200mm | Cold-Rolled&Hot-Rolled | Annealed,Solution and Aging,Q+T,ACID-WASHED,Shot Blasting |
| Pipes/Tubes | Seamless Pipes/Tubes,Welded Pipes/Tubes | OD:6-219mm x WT:0.5-20.0mm | Hot extrusion,Cold Drawn,Welded | Annealed,Solution and Aging,Q+T,ACID-WASHED |
| Grade | Standard | Country | Application |
|---|---|---|---|
| 18Ni Maraging Steel | AISI | USA | Typical applications for maraging include missile and rocket motor cases, landing and takeoff gear, munitions, aerospace, extrusion tooling, die casting, high performance shafting, gears and fasteners. |
| G3500 | AISI | USA | Used in the products of the automobile, truck, tractor, and allied industries |
| G3500b | AISI | USA | Diesel engine cylinder block, truck and tractor cylinder block and cylinder head, flywheel, tractor transmission case and heavy-load gear box |
| G3500c | AISI | USA | Used in the products of the automobile, truck, tractor, and allied industries |
| A 693 S35000 | AISI | USA | Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip |
| S35000 | AISI | USA | Precipitation Hardenable Chromium Nickel Molybdenum Stainless Steel |
| SA-693 S35000 | AISI | USA | Specification for Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip |
| A 693 S35000 | AISI | USA | Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip |
| S35000 | AISI | USA | Precipitation Hardenable Chromium Nickel Molybdenum Stainless Steel |
| SA-693 S35000 | AISI | USA | Specification for Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip |
| A 693 Type 633 | AISI | USA | Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip |
| A 959 Type 633 | AISI | USA | Standard Guide for Specifying Harmonized Standard Grade Compositions for Wrought Stainless Steels |
| AM-350 | AISI | USA | Steel Sheet and Strip, Corrosion and Moderate Heat Resistant 16.5Cr - 4.5Ni - 2.9Mo - 0.10N Cold Rolled, Tempered |
| AM-350 | AISI | USA | Steel, Corrosion and Heat-Resistant, Sheet and Strip 16.5Cr - 4.5Ni - 2.9Mo - 0.10N 1850 to 1975 °F (1010 to 1079 °C) Annealed |
| AM-350 | AISI | USA | Steel, Corrosion and Heat-Resistant, Seamless Tubing 16.5Cr - 4.5Ni - 2.9Mo - 0.10N Annealed |
| AM-350 | AISI | USA | Steel, Corrosion and Heat-Resistant, Bars and Forgings 16.5Cr - 4.5Ni - 2.9Mo - 0.10N Equalized and Over-Tempered |
| AM-350 | AISI | USA | Steel Sheet and Strip, Corrosion-Resistant, Precipitation Hardening (AM350 and AM355), Premium Quality Composition AM350, Annealed Composition AM355, CRT 150/180/120 |
| AM-350 | AISI | USA | Steel Sheet and Strip, Corrosion and Moderate Heat Resistant 16.5Cr - 4.5Ni - 2.9Mo - 0.10N Cold Rolled, Tempered |
| AM-350 | AISI | USA | Steel, Corrosion and Heat-Resistant, Sheet and Strip 16.5Cr - 4.5Ni - 2.9Mo - 0.10N 1850 to 1975°F (1010 to 1079°C) Annealed |
| AM-350 | AISI | USA | Steel, Corrosion and Heat-Resistant, Seamless Tubing 16.5Cr - 4.5Ni - 2.9Mo - 0.10N Annealed |