Home»Grades > Special Alloy > O1

ASTM O1Enquiry|Print this page

O1Application:Alloy tool steel
CategoryTypeSteel gradeStandardCountry
Grades Special Alloy O1ASTMUSA

Chemical composition%of the ladle analysis of gradeO1

C(％)Si(％)Mn(％)P(％)S(％)Cr(％)V(%)W(%)
0.85～1.000.10～0.501.00～1.40≤0.030≤0.0300.40～0.60≤0.300.40～0.60
O1
Mechanical properties of gradeO1
Proof strength
Rp0.2(MPa)		Tensile strength
Rm(MPa)		Impact energy
KV(J)		Elongation at fracture
A(%)		Reduction in cross section on fracture
Z(%)		As-Heat-Treated ConditionBrinell hardness(HBW)
332(≥)318(≥)114211Solution and Aging,Annealing,Ausaging,Q+T,etc321
Physical properties of gradeO1
PropertyDensity
kg/dm3		Temperature T
°C/F		Specific heat
J/kgK		Thermal conductivity
W/mK		Electric resistance
µΩ·cm		Modulus of elasticity
kN/mm2		Expansion rate
263(≥)474(≥)441121Solution and Aging,Annealing,Ausaging,Q+T,etc441
Temp.
°C/°F		Creep strain limit
(10000h)
(Rp1,0)N/mm2		Creep rupture strength
(10000h)
(Rp1,0)N/mm2
259265622
O1Range of products
Product typeProductsDimensionProcessesDeliver Status
Plates/SheetsPlates/Sheets0.08-200mm(T)*W*LForging,hot rolling and cold rollingAnnealed,Solution and Aging,Q+T,ACID-WASHED,Shot Blasting
Steel BarRound Bar,Flat Bar,Square BarΦ8-1200mm*LForging,hot rolling and cold rolling,CastBlack,Rough Turning,Shot Blasting,
Coil/StripSteel Coil/Steel Strip0.03-16.0x1200mmCold-Rolled&Hot-RolledAnnealed,Solution and Aging,Q+T,ACID-WASHED,Shot Blasting
Pipes/TubesSeamless Pipes/Tubes,Welded Pipes/TubesOD:6-219mm x WT:0.5-20.0mmHot extrusion,Cold Drawn,WeldedAnnealed,Solution and Aging,Q+T,ACID-WASHED
Cross Reference Table(Equivalent Grade)
GradeStandardCountryApplication
00Cr17Ni14Mo2ASTMUSA
Austenitic stainless steel. Grade 00Cr17Ni14Mo2 was replaced by new designation 022Cr17Ni12Mo2 according to GB/T 20878 (2007)
X2CrNiMo18-14-3ASTMUSA
Austenitic stainless steel. Grade 00Cr17Ni14Mo2 was replaced by new designation 022Cr17Ni12Mo2 according to GB/T 20878 (2007)
1.4435ASTMUSA
Austenitic stainless steel. Grade 00Cr17Ni14Mo2 was replaced by new designation 022Cr17Ni12Mo2 according to GB/T 20878 (2007)
Z 3 CND 17-11-02ASTMUSA
Austenitic stainless steel. Grade 00Cr17Ni14Mo2 was replaced by new designation 022Cr17Ni12Mo2 according to GB/T 20878 (2007)
TS 60ASTMUSA
Austenitic stainless steel. Grade 00Cr17Ni14Mo2 was replaced by new designation 022Cr17Ni12Mo2 according to GB/T 20878 (2007)
X70CrMo15ASTMUSA
Stainless steels - Part 3: Technical dStainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposeselivery conditions for semi-finishe
1.4109ASTMUSA
Stainless steels - Part 3: Technical dStainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposeselivery conditions for semi-finishe
X55CrMo14ASTMUSA
Stainless steels - Part 3: Technical dStainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposeselivery conditions for semi-finishe
1.4110ASTMUSA
Stainless steels - Part 3: Technical dStainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposeselivery conditions for semi-finishe
X6CrMo17-1ASTMUSA
Steel rod, bars and steel wire for cold heading and cold extrusion - Part 5: Technical delivery conditions for stainless steels
1.4113ASTMUSA
Steel rod, bars and steel wire for cold heading and cold extrusion - Part 5: Technical delivery conditions for stainless steels
X20CrMo13ASTMUSA
Rolled, Wrought or Cast Stainless Steel Products for Medical Instruments
1.4120ASTMUSA
Rolled, Wrought or Cast Stainless Steel Products for Medical Instruments
X39CrMo17-1ASTMUSA
Stainless steels - Part 3: Technical dStainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposeselivery conditions for semi-finishe
1.4122ASTMUSA
Stainless steels - Part 3: Technical dStainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposeselivery conditions for semi-finishe
X105CrMo17ASTMUSA
Stainless steels - Part 3: Technical dStainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposeselivery conditions for semi-finishe
1.4125ASTMUSA
Stainless steels - Part 3: Technical dStainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposeselivery conditions for semi-finishe
32CrMo12ASTMUSA
Nitriding steel
1.7361ASTMUSA
Nitriding steel
X5CrNiMo17-12-2ASTMUSA
DIN 1654-5 (1989) Cold heading and cold extruding steels; technical delivery conditions for stainless steels; Replaced by DIN EN 10263-5:2002

Relevant products

Enquiry